LED lighting, soundproof, Sailor's Solutions Inc.      
 
product<br>image
Click to Enlarge

RT001 3M™ Scotchlite™ SOLAS Reflective Tape 2 inch wide- SOLD BY THE FOOT
See and be seen! Sold by the foot
$1.79

View Cart

If you've ever had a close call in a dingy or didn't see someone dangerously close we're sure you'll attest to the safety value of 3M™ Scotchlite™ Reflective tape. It is SOLAS (Safety of Life at Sea) Grade tape and is ideal for the following applications and more:
  • hard & inflatable dingies
  • sail covers & sails
  • life vests
  • life rings
  • jackets
  • mooring balls
  • docks & pilings
  • kayaks & rowing shells
This product conforms to the Marine Equipment Directive 96/98/EC and International Maritime Organization (IMO) Resolution A.658 (16) Annex 2. In addition, it is approved by the U.S. Coast Guard to meet 46 CFR part 164, Subpart 164.018 requirements for Type I and II retroreflective materials. Scotchlite reflective material – SOLAS grade tape helps enhance visibility of life-saving equipment in nighttime, or low-light conditions when illuminated by a spotlight or other light source.

This reflective tape is silver, flexible and reflective with a pressure sensitive adhesive. The tape can be used on the following substrates:
  • Rough surfaces
  • Glass reinforced polyester
  • Aluminum
  • Rubber coated cloth
  • Rubber film
  • Vinyl or PVC films
  • Polyurethane film
  • Polyester fabric (varies with treatment)
  • Nylon fabric
  • Cotton drill (thicker weave)
The tape is comprised of an encapsulated lens optical design that provides high reflectivity over a wide range of entrance angles, whether dry or wet. Scotchlite reflective material – SOLAS grade products have a European mark of conformance.

Directions:

The coated fabric must be clean, dry, and substantially free of contamination. If necessary, wipe the substrate surface with a mild solvent, such as VM & P Naphtha or mineral spirits (test the solvent first on a small area of the fabric to make sure the surface is not damaged).

The minimum application temperature is 60°F (15°C). Whenever possible, remove flotation material or deflate equipment,
and smooth out wrinkles.

  1. Hand cut or cut with a scissors to the desired size
  2. Separate approximately 1” of liner paper from reflective material. Bend liner back onto itself.
  3. When everything is properly aligned, press down the exposed adhesive area with a squeegee starting from the inside and working towards end.

NOTE: It is recommended, to improve adhesion, to allow 48 hours (above 60°F) before handling, inflating, or packaging.

product<br>image
SCAD TM2 Tank Monitor for Two Tanks (sensors sold separately)
Monitor two tanks with the touch of a button.
$135.00
product<br>image
Winch Handle Holder

$24.95
product<br>image
Signal Mate 2NM LED Tri-Color plus Anchor, Wind Indicator Illumination and Daylight Sensor (bracket included)
Compact and rugged Designed for many years of operation. Daylight sensor turns Anchor light on/off Made in USA!
On Sale through February. MSRP $371.00, Now $310.00!
$310.00
product<br>image
WinchRite ABT Cordless, Lightweight, Electric Winch Handle
Boat Show Special through February! Instantly electrify all your winches!
$749.00
product<br>image
SmartLock outboard motor lock for engines to 35/40 HP

Keep your engine safe from thieves!
$98.95
product<br>image
Perfect Pole Telescopic Handle for Hooknife Rated #1 by Powerboat Reports!
This is the best pole/handle for our line slicing Hooknife. Extends your Hooknife's reach by 6'
$34.95
product<br>image
SCAD LVA Low Voltage Monitor with Alert & Relay
It's programmable! Don't let your batteries go low without warning Shuts off or turns on electrical devices automatically
$79.95
product<br>image
Signal Mate 3 NM LED Anchor Light with Photocell that Turns light on at Dusk and off at Dawn
Compact and rugged Designed for many years of operation Made in USA!
On Sale Now. MSRP $246.00, Now $199.95!
$219.95

Go to top of page.